In the previous lecture we seen how easy it is to kreipe debut epee.
All we have to do is capture enough data and then draw on aircraft energy to crack the encryption and
give me the key.
Now one problem that we could face is if the network is not busy.
If it's not busy then the number of data will be increasing very very slowly.
Therefore we're going to have to wait for a while before we have enough data to crack the key.
So let me show you an example.
I'm just going to run.
Error.
Dump energy here and list all the networks around me.
And you can see I have my test network my test AP in here is in web.
If you look under the data you'll see that it's at zero.
And it's not increasing.
And even if it's going to increase it's going to increase very very slowly which means that I'm going
to have to be waiting for hours before I can crack this network.
So a solution to this is to forest the AP to generate new packets with New ivie's.
Now before doing this we need to associate with this network.
So what I mean by associate is we need to tell this network that we want to communicate with it because
by default access points ignore any requests they get unless the device has connected to this network
or associated with it.
So don't get this mixed up with connecting.
Were still able to connect to the network because we need the password to be able to connect to the
network.
What were what were doing right now is literally just telling the target network look I want to communicate
with you.
Dont ignore my requests.
Thats all were doing it.
So its something similar to what happens when you just click on the network when you want to connect
to it.
You still have to put the password you're just in the target network.
I want to communicate with you.
Please don't ignore me.
So in this lecture I'm going to show you how to associate with the target network so we can communicate
with it.
And in the next lecture I'm going to show you how I was associated We can inject packets into the network
and forest the number of data to increase very very quickly.
First I'm going to run over them and against my target network which has this BSA cida So I'm going
to copy it and we're going to use the exact same command that we have been using so far.
So we're going to do it or dump and G.
That should I should.
Yes yes I did.
Followed by the mike address of my tower did that.
That ash Channel.
Followed by the channel which my target is running go on which is six.
And we were going to store all of this so we're going to do a dash dash right and we'll call this file
a our AP replay because thus the name of the attack.
And then I'm going to put my wireless adapter in monitor mode which is zero.
So a very simple command that we'd done before were using error dump energy to capture data from our
network with this MAC address running on this channel.
We're a story in everything and a file called arpu a play.
I'm going to have a..
And as you can see it's running against my target.
I noticed that there is increasing really really slow or it's actually not increasing at all right now.
Now to associate with this network will it go on to use a program called Air replay energy.
So we're going to type a reply energy followed by a dash dash fake.
Because we want to do a fake authentication attack.
We're going to with zero because we all knew what to do with this once we were going to do a dash 8
to specified the Mac address of the target network.
So I'm going to paste it I've already copied it.
Then we're going to do a dash page to specify the Mac address of my wireless adapter and to get the
MAC address of my wireless adapter.
I'm going to do if config.
It's the first 12 digits of the unspeak field.
Usually you'd see it after the other but when you enable monitor mode it'll show up like so.
So I'm going to copy this.
I'm going to paste it here.
And I'm going to replace the minuses with.
Call on.
And that's it.
It's done.
And finally I'm just going to give the name of my wireless adapter in monitor mode.
So a very simple command.
We use an aeroplane engine which is a tool that can be used to run a number of attacks and we see news
seen this with the authentication attack were still at it.
We want to run a fake authentication attack.
We want to do with this once we are giving it the MAC address of my target network after the A.
Then I'll give it the MAC address of my wireless adapter after the rage.
And finally I'm giving it my wireless adapter in monitor mode.
Now before I run this notice in here under the off we have nothing and we don't have any clients show
up in here at the bottom.
No if I hit enter you can see under the earth it's showing up as open and you can see we have a new
client here associated with the network.
If you look in here you'll see this is the MAC address of my target network.
And right here is the MAC address of my wireless adapter.
So right now I am associated with the terrorist network.
And if I send it anything it's going to accept it and it's going to communicate with me again.
I am not connected to the network.
I still can't use the Internet.
I'm literally just associated with the network so I can communicate with it.
Now in the next lecture I'm going to show you how we can communicate with this network in a way to force
it into generating new packets with New ivie's which will allow us to crack the key very very quickly.