In the previous video, we have learned about trunk. 2
Next in this video, we are going to create one more topology, 3
let’s say we will create topology for room 3. 4
Let’s import a new switch. 5
But I will not use 2960 again, I will use 3560. 6
Actually this two switch is similar, but there are some differences between this two switch. 7
We will talk more about the differences in the next video. 8
Then now let’s add 4 pc like before. 9
To add some pc at once, here we can type ctrl or control in the keyboard, click the pc, 10
release the control button and here we can add some pc at once. 11
Now let’s change the name of the pc, here the last pc is pc 10, so this will be pc 11, 12
pc 12, pc 13 and last pc 14. 13
Now let’s connecting the pc to the switch. 14
Here we also can use ctrl to add some cable at once. 15
So type ctrl in the keyboard, click on the cable, release the ctrl. 16
And now we can connecting all pc to the switch. 17
Okay, now let’s configure the vlan in the switch. 18
Here we get a question, would you like to enter the initial configuration? 19
We can choose no here. 20
Enable, and then configure terminal. 21
Let’s create the vlan first, vlan 10 the name is accounting, and then vlan 20, 22
the name is marketing. 23
Let’s verify it. 24
Do show vlan brief. 25
Okay here we can see that now we have vlan 10 and vlan 20. 26
But all of the interface is still in the vlan 1. 27
Now let’s assign fa0/1 and fa0/4 to the vlan 10. 28
If you remember in the previous video, we can use interface range to assign some interface 29
to the vlan at once. 30
Let’s say here we want to assign fa0/1 and fa0/2 to the vlan. 31
And if we use interface range fa0/1 until 4, so fa0/1, fa0/2, fa0/3, 32
fa0/4 will be assigned to the vlan. 33
But in this case, we only want to assign the interface fa0/1 and fa0/4. 34
Because fa0/2 and fa0/3 is in the vlan 20. 35
To do this, we can use comma, so interface range fa0/1, fa0/4 like this. 36
Then switchport mode access, switchport access vlan 10. 37
Let’s verify it. 38
Do show vlan brief. 39
Okay here we can see that now fa0/1 and fa0/4 is in the vlan 10. 40
Next let’s assign fa0/2 and fa0/3 to vlan 20. 41
Interface range fa0/2-3. 42
Switchport mode access, switchport access vlan 20. 43
Let’s verify it again, do show vlan brief. 44
Okay here we can see that now fa0/2 and fa0/3 is in the vlan 20. 45
Last, let’s configure the ip address of all pc. Here for pc 11, the ip address is 192.168.1.11. 46
pc 12 the ip address is 192.168.1.12. 47
pc 13 the ip address is 192.168.1.13, and last, pc14 48
the ip address is 192.168.1.14. 49
Now let’s test the connection between pc in the same vlan. 50
Let’s ping between pc in the vlan 10. 51
Okay successful, next let’s test between pc in the vlan 20. 52
Okay this is also successful. 53
Okay I think enough for this video. 54
Here we already create a new topology for room 3. 55
In the next video, we are going to connecting this room 3 with room 1 and room 2. 56
Thankyou for watching and see you on the next video.